You'll Never Guess This Replace Door Lock's Benefits

How to Replace Door Locks

Door locks are your first security measure against unauthorized access to your home. Locks may need to be replaced due to signs of wear and tear or other circumstances like moving into a new home or a break-in.

To begin, determine the size of your cylinder using the distance between the adjustment screw and the center of the cylinder knob. This measurement will help you select the appropriate lock.

Deadbolt

If you're looking to ensure that your door is safe from intruders, it's a good idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe, it makes it much more difficult for an intruder through the door. A single-cylinder deadbolt is activated using a key on the exterior, and a thumb-turn device that is located inside. Deadbolts will only work when it is properly installed.

The first step is to determine if the upvc door locks replacement already has a hole for deadbolts, or if it has to be bored. Mark the location of the hole to install the deadbolt on the exterior of the door using the template that came with your lock installation kit. Then, use the tape measure to determine how high the deadbolt should be. Then, mark the high point on the outside of the door. You can then use the speed square to draw an even line across the mark you made for the bolt hole.

Next, use a power drill to bore out this area until the hole reaches the other side of the door. It may take a while. Then, sand down the hole and the edges of the door so that it is smooth. At this point, it's a good idea to stain or paint your door.

Remove any screws that are visible from the deadbolt. This will reveal the back and front assemblies of the deadbolt as well as the bolt that is inside. Then unscrew the old bolt and replace it by an alternative bolt that matches the door hardware. You'll need to remove the bolt from the setplate. After this is done it is time to chisel the area for the strike plate on the door frame.

If your strike plate is not in alignment it could be because the previous installer failed to mortise it properly, or a weatherstripping changed the strike position. It is necessary to re-mortise the strikeplate and possibly even the deadbolt itself to fix this issue. Close and lock the deadbolt when you've completed this step. Test the deadbolt by closing and locking it once the bolt has been extended into the strike plate.

Knob

If a door replace door lock knob wears out it could make your business or home less secure. It could make it more difficult to open or close the door, so it's an ideal idea to replace door Lock it. It shouldn't take you more than 30 minutes. You can use a screwdriver or pliers to get rid of the knob or handle, but be careful not to harm any of the other components on the door.

Before starting, you'll want to spray WD-40 or some other dry lubricant on the mechanism of the knob on your door. This will allow the new lock to slide smoothly when you turn it. To ensure that it operates properly, it's important to choose a knob and handle that match your existing doors. If you don't have a doorknob that is compatible and handle, you'll need to purchase a new one.

To begin the replacement door lock process, first examine the old knob or handle to find the screws that hold it in place. If there aren't any screws to hold it in place, you can use a screwdriver to insert the cover plate in between the screws plate that is hidden.

After you have removed the knob examine it for evidence of damage or rust. If the knob is damaged or has dents or marks then you'll need to clean it. Otherwise it shouldn't require any major work.

Now it's time to install the new knob. It is important to first look over the two knobs in order to make sure that you've chosen the right one for the door. You'll want to pick one with an extended rod designed to interlock with the second knob's rod mechanism. After you've placed the new knob into the hole and then put it in the latch.

Thread the latch plate screws downwards and then test the spring by pressing down repeatedly. The latch should rise every time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread the long screws of the interior doorknob through the cylinder holes on the exterior knob and secure it in its place.

Latch

A latch is a steel piece that extends into the replacing patio door lock jamb to keep it closed. The latch can be operated by a knob or handle on the interior of the door, or by a thumb-turn on the exterior. A deadbolt can be used to secure a latch and keep burglars from piercing the glass of the door. It also offers protection from accidental or intentional closing of the door by pets or children. The latch can be fitted with single cylinder deadbolts or a double cylinder deadbolt, according to the security level you prefer.

Installing a latch involves the same steps similar to installing a deadbolt but there are a few distinctions. First, determine the setback of the doorjamb with an instrument to make sure the new lock will fit. The setback is the distance between the edge of the doorjamb, to the center of the hole for the faceplate for the latch. A standard setback is 2 3/8 to 2 3/4 inches. If your setback is greater than that, you might need to purchase a latch that is longer from a hardware or locksmith store.

The next step is to drill an edge bore hole in the doorjamb to accommodate the latch plate. Utilize a chisel to smooth out the mortise for the latch and ensure it's deep enough for the faceplate of the new latch to be close to the doorjamb. Put the strike plate into place to make sure it's in the right position.

If the strike is too high, you can kick the door in or apply pressure using an iron tire or crowbar. This could cause the doorjamb's to crack. This can be corrected by drilling a new hole through the doorjamb, then cutting the core from the hole that was previously made.

The final step is to mount the new strike plate, which can be done by screwing it over the existing screw holes. Utilize wood putty to fill in any old bolt holes or screw holes that aren't being used. After the putty is dry, sand it to an even finish.

Strike

An electric strike is a metal piece that holds the deadbolt and latch are engaged when the door is closed. It is a vital component of the security of a lock, because it seals the door and offers additional resistance to kicking or force applied to the door. If a door comes with an electronic strike, it will be opened by using keys and the control unit that controls its electrical impulses.

In the past, installing an electronic strike required cutting a piece of a doorjamb in order to let the latchbolt of a cylindrical lock from the pocket that is inside the strike. This is an inconvenience in regards to the aesthetics of an opening and also exposes the mechanism of the latchbolt and keeper to unintentional users.

Recently, several electric strikes manufacturers have created a "No Cut" kind of strike that does not require a cutout for operation. These strikes have a unique design to allow the latchbolt and keeper to slide into the strike pocket without marring the doorjamb faceplate.

The strike has an internal ramp that raises the latchbolt and keeper when it receives an electrical impulse from a reader or controller. The retraction of the keeper and latchbolt pushes them up higher on the ramp, which locks the door. When the door is closed the deadbolt remains in extended and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward process, particularly if you're replacing upvc door lock an existing strike. If you're planning to upgrade an access control system to an electric strike, it is important to ensure that the new system is compatible. Also, you must ensure that the strike is properly connected to your access control system and that it is set up for fail-safe operation.

Upgrade your strike plates with heavy duty strike plates to block the entry of unauthorized persons. The plates utilize four to six three-inch screws instead of the two, three-fourth inch screws typically used in standard strikes. The longer screws make breaking the frame to reach the piece that turns the thumb on a single deadbolt cylinder more difficult.